Видео

Thank you for this! I'm learning how to improve with tig and your videos are helping tremendously! Thank you!

Thank you so very much

❤

Help! My root keeps coming out too flat on the inside and I don't know what I'm doing wrong!

Are you swapping between your right and left hand for each side or are you using your right throughout the vid?

Muy buena tecnica gracias

Super program! Brawo😊

Great job bro. What are you using to tac, piece of rod? Also, roughly how long did it take to weld up?

How do you stop from slipping! I keep slipping on the bottom!

Very good welder!!!

Very good welder!!!

Just passed my 6G Tig all the way out and Tig/7018 combo thanks for all the vids

Puts way too much heat into the plate

Question for the tungsten electrode is the tip always completely sharp or should it be alittle blunt flat on the end cause when I do ac welding with aluminum for example it’s supposed to kinda ball up be a little blunt or like bullet shape I believe not as narrow as I would for like using mild steel or stainless steel in dc just curious my welding fundamentals 6th edition says that

What amps did you run the cap beads bro?

Can you do a video of one pass… but a vertical… not a horizontal?? 🙏🏼🙏🏼

Qual amperagem vc usou?

Hi guys can someone describe for me what is a double coded welder

Golden weld of doom.

having issues with the bottom root, if i have the filler rod inside the pipe on the bottom i get a couple bumps on the root, if i go more amps it gets worse if i go less amps like 70 there less bumps but it feels way to cold

Lleva gas adentro ?

oh my ..thats Beautiful root pass 😭 i got strugle on feeding the roddd

good welding

Thank you again for another great video! Your little angel, be blessed with your children. Your work ethic and raising your family, one will compliment the other! Kind of what Mel Gibson said in “we were soldiers! Stay blessed! I’m spending more hood time on my tig!

Fantastic. For me was awesome to see you in action. I’m not a welder and this is helping a lot to understand. I had e question. At the beginning you highlighted the maximum root on the inside. Is this value defined? Any suggestion on the surface finishing for oxygen? Any suggestion in this direction is welcome. Thank you

Thanks for sharing ❤️‍🔥💞❤️‍🔥💯✅👏

❤❤❤تشکر عزیزم

Ist oke veri good

Hello gentlemen, In pass on,or root pass all your attentions were accurate, from the presence of tungsten and the necessary amount that should be outside of the ceramic, as well as the size of the tube gap to have good penetration to take X-rays, thank you for your accuracy.

Nice ❤vivideo sir 🇮🇳🇮🇳🇮🇳🙏

16:25 isnt that a single pore?

As i can see the preparing is very important. Thanks for this video ❤

How would that material weld out using a shield gas of Argon + 2 1/2% Hydrogen to help remove oxides from the pool and to make it more fluid

6:46 where can i get this ??

You should never start and stop in the same spot if x - rayed. Can have lack of fusion

Thanks, I found this very useful.

Masterly and a joy to watch. Just the relaxed explanation to make it understandable to everyone is a gift for which my big thanks. Greetz from Holland, Marcel Knippers😃

Awesome job first of all and even better job explaining and teaching. So much out there that’s just junk on RUclips but not here. Why the 80d wire? What was the pipe?

Красивый шов 👍

I don’t understand how fill to flush in one pass

Odakle si druze, rekao bih po naglasku da si sa Balkana.

Thanks for ur tips u the best teacher one question for me Sasol South Africa when u weld at the bottom ur wire is move side to side push or u just push it at the center???

Thank you for the content,very informative and helpful

Perfect welding my brother 👍👍👍

Awesome

I've been struggling more on my root penetration when I hit the top side of my 6 G

Turnaround and new construction welder here out of Houston Texas bro i gotta give you your credit where its due i passed so many tests from watchin your videos alone. I just signed up for a boilermaker union down here about to take my 6G tube test in August. You're right on time with this one. Also can you post an updated one with tig root 7018 feel and cap. Appreciate the tutorials bro if theres a way to support i will

Can you make a video of how you sharpened tungsten and what types of tungsten do you use ?

Your so good not only tig weld with constant feed but recording with another hand thanks for the videos

👏👏👏🤝🤝🤝